06-3210 Dual Tap Transformer - Installation Guide
Resource ID
988
Access
Open
Contributed by
Derek Rennie
Updated date
28 March 24
Title
06-3210 Dual Tap Transformer - Installation Guide
Keywords
7
Product Range
Genius
Language
UK English
Company Brand
Peak Scientific
Part Number
IG-06-3210
Reviewed on 3rd May 2017 - LC
Extracted text
Installation Guide
06-3210 Dual Tap Transformer 200V – 230V
For All Genius 30 Series Generators
INSTALLATION
1.
2.
Remove the transformer from all
the packaging, ensuring that the
two securing screws are retained
and not thrown away.
3.
Ensure that the generator to
which the transformer is to
be fitted is switched OFF on
the front panel.
4.
Remove the mains
cable from the mains
supply socket.
5.
Once safely disconnected from the
mains, remove the generator side panel.
Model Genius 30 Series
Fountain Crescent
Inchinnan Business Park
Inchinnan, PA4 9RE
Scotland, UK
6.
Using the Hex-Key
provided in the
fittings kit, turn the
lock 90o clockwise.
Remove the panel from the
generator.
An earth lead is connected
to the inside of the panel.
This can be removed by
pulling it off the spade
connector on the door.
T: +44 (0)141 812 8100
F: +44 (0)141 812 8200
W: www.peakscientific.com
E: info@peakscientific.com
Part No. IG-06-3210
Rev.
2
Page
Page 1 of 5
7.
8.
9.
ATTENTION
Do not touch anything
inside the generator while
the side panels are
removed and the mains
power is connected to the
unit.
Plug the mains cable into
an appropriate 230VAC
50/60Hz single phase
power supply
Switch the generator power ON
at the switch on the front panel.
10.
The voltmeter is located at the top of the electrical panel. This will measure and display the
mains voltage that is being supplied to the generator. Note the displayed voltage.
>=220
<=253
<=219
>=194
=
If the voltmeter reads a voltage of between 220V and
253V the mains supply is sufficient and the transformer
should not be fitted.
=
If the voltmeter reads a voltage between 194V and
219V then the transformer is required. Proceed with
the installation of the transformer.
Fountain Crescent
Inchinnan Business Park
Inchinnan, PA4 9RE
Scotland, UK
T: +44 (0)141 812 8100
F: +44 (0)141 812 8200
W: www.peakscientific.com
E: info@peakscientific.com
Part No. IG-06-3210
Rev.
2
Page
Page 2 of 5
11.
12.
Switch the generator power OFF at the
switch on the front panel.
Remove the mains cable completely from the
power supply and then unplug from the rear
of the generator.
**NOTE**
The transformer has a ‘Dual Tap’ facility. This allows it to cover a broarder range of low
supply voltages. The transformer will be supplied with the 200V tap already connected.
This will be required for most applications.
If the additional 208V tap is required, then this can be easily changed before connecting to
the generator.
Voltage Reading
197V to 212V
Voltage Reading
213V to 219V
The 200V tap is required, no modification to the
transformer is necessary. Progress to stage 16.
The 208V tap is required. It is necessary to change the
tap inside the transformer. This is very easy and can be
done by following stage 13. to stage 15.
13.
14.
Place the transformer on its back and
remove the cover retaining screw using
either a flat blade screwdriver or ¼”
spanner. The cover can then be removed.
Fountain Crescent
Inchinnan Business Park
Inchinnan, PA4 9RE
Scotland, UK
The ‘Primary Taps’ are now exposed. These
are clearly labelled ‘200V’ and ‘208V’. To
change the tap simply pull the connector
labelled ‘200V’ off the spade terminal and
push the connector labelled ‘208V’ fully on to
the terminal. The ‘200V’ tap wire removed
can be safely left loose in the compartment.
T: +44 (0)141 812 8100
F: +44 (0)141 812 8200
W: www.peakscientific.com
E: info@peakscientific.com
Part No. IG-06-3210
Rev.
2
Page
Page 3 of 5
15.
16.
Replace the transformer cover and securly
fasten with the retaining screw. The
transformer is now ready for mounting on
the rear of the generator.
The mounting screws provided can be
screwed into the holes on the rear of the
generator. Leave approvimately 5mm
protruding. The transformer can then be hung
on the protruding screws. Once located
correctly the screws can be fully secured.
17.
18.
Plug the mains cable from the transformer,
labelled ‘TO GENERATOR’ into the mains
socket on the rear of the generator.
19.
Plug the original generator mains cable into
the mains inlet socket on the transformer,
labelled ‘MAINS INPUT’.
20.
Plug the mains cable back into the original
single phase mains power supply and
ensure the power is switched ON.
Fountain Crescent
Inchinnan Business Park
Inchinnan, PA4 9RE
Scotland, UK
Switch the generator ON again at the switch
on the front panel.
T: +44 (0)141 812 8100
F: +44 (0)141 812 8200
W: www.peakscientific.com
E: info@peakscientific.com
Part No. IG-06-3210
Rev.
2
Page
Page 4 of 5
21.
22.
The voltmeter should now read above
220V. If it is still below 220V and you have
not fitted the ‘208V tap’, disconnect the
transformer and return to stage 13.
23.
Switch the generator OFF on the front panel
and disconnect from the mains supply.
24.
Re-attach the side panel to the generator,
taking care to ensure the earth lead is
reconnected correctly. The locks are
secured by turning the lock 90o
anticlockwise using the hex key provided.
Once the side panel is securely assembled,
the mains power supply can be reconnected
and the generator switched back ON.
CONGRATULATIONS
You have now successfully installed the transformer on your PEAK SCIENTIFIC gas
generator. The generator is now operational and ready to supply gas on demand to your
instrument.
If you should have any problems or require further support please contact our Technical
Helpdesk on the following numbers
Europe (ROW)
+44 (0)141 530 4180
North America
+1 866 732 5427
India
+91 (0)40 2780 0663
support@peakscientific.com
usasupport@peakscientific.com
indiasupport@peakscientific.com
Fountain Crescent
Inchinnan Business Park
Inchinnan, PA4 9RE
Scotland, UK
T: +44 (0)141 812 8100
F: +44 (0)141 812 8200
W: www.peakscientific.com
E: info@peakscientific.com
Part No. IG-06-3210
Rev.
2
Page
Page 5 of 5