50 Series - User Manual 

Resource downloads

File information File dimensions File size Options

Original PDF File

1.5 MB Download

Screen

566 × 800 pixels (0.45 MP)

4.8 cm × 6.8 cm @ 300 PPI

30 KB Download

Preview

Full screen preview

30 KB View
Resource details

Resource ID

174

Access

Open

Contributed by

Liam Couttie

Updated date

-

Review date

03 May 19

Title

50 Series - User Manual

Revision Number

1

Keywords

7

Product Range

Other

Company Brand

Peak Industrial

Public / Private

public

Reviewed on 3rd may 2017 - LC

Extracted text

50 Series User Manual

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual

Contents
Change History How to use this manual Introduction Warranties and Liabilities Safety Notices Symbols Safety Notice to Users Environmental Declaration Technical Specification Environment Generator Outlets Electrical Requirements General Technical Specification Environment Generator Outlets Electrical Requirements General Unpacking Installation Generator Environment General Dimensions Unit Controls Rear Connections Fittings Kit Drain Connection Air Connection Electrical Connection 4 4 5 6 7 7 7 8 9 9 9 9 9 10 10 10 10 10 11 12 12 12 13 14 14 14 15 15

Page 2

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual

Commissioning Tubing Lengths IMPORT ANT DOCUMENTS Normal Operation On Demand Gas Cleaning Service Requirements Service Schedule Safely Isolated Condition Safe State After Repair Product Overview

16 16 17 18 18 18 19 19 19 20 21

Breathing Air Filter Element Replacement 22 RAC Filter Element Replacement Pressure Switch Overview Pressure Settings Procedure to set Pressure Switch Trouble Shooting i-Flow 5010 Pneumatic Schematic Rev 1 i-Flow 5020 Pneumatic Schematic Rev 2 i-Flow 5030 Pneumatic Schematic Rev 1 i-Flow 5040 Pneumatic Schematic Rev 1 i-Flow 5050 Pneumatic Schematic Rev 1 i-Flow 5060 Pneumatic Schematic Rev 1 i-Flow 5070 Pneumatic Schematic Rev 1 i-Flow 5080 Pneumatic Schematic Rev 1 i-Flow Electrical Schematic Rev 1 22 24 24 24 24 26 27 28 29 30 31 32 33 34 35

Page 3

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Change History
Rev. 1 2 3 4 Comment Updated Service Kit Information Name Liam Couttie Date 16/04/2014

How to use this manual
This manual is intended for end users and has been written so that it can either be read as a step by step guide to installation and usage; or as a reference document where you can skip to the relevant information. Please review each of the following sections carefully. Thank you for selecting Peak Industrial to meet your Gas Generation needs, should you require any further assistance or support please do not hesitate to contact Peak Industrial or the Peak Partner from which you purchased your Generator

Page 4

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Introduction
The Peak Industrial i-Flow 5000 Generator is designed to cater for the requirements of a wide range of industrial and scientific applications that require a pure, dry and phthalate-free source of nitrogen gas. Your generator will have been carefully selected to meet your specific pressure, flow and purity requirements. If you have any questions regarding the sizing of your system please do not hesitate to contact Peak Industrial or the Peak partner from which you purchased your Generator.

Page 5

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Warranties and Liabilities
1. The Company warrants that it has title to the Goods. 2. Subject to the provisions of this clause the Company warrants that the
Goods shall comply in all material respects with any specification referred to in the Order Confirmation (as the same may be amended) and shall, subject thereto, be free from defects in material and workmanship for the lesser of a period of twelve months from the date of delivery or thirteen months from the date of dispatch from the factory. Save as provided in this clause and except where the Goods are sold to a person dealing as a consumer (within the meaning of the Unfair Contract Terms Act 1977) all warranties, conditions or other terms implied by statute or common law are hereby expressly excluded save to the extent they may not be lawfully excluded. When the Goods are sold to a consumer within the meaning of the Unfair Contract Terms Act 1977 their statutory rights are not affected by the provisions of this clause. In the event of the Customer making a claim in respect of any defect in terms of clause 2 hereof the Customer must. 4.1. Reasonably satisfy the Company that the Goods have been properly installed, commissioned, stored, serviced and used and without prejudice to the generality of the foregoing that any defect is not the direct or indirect result of lack of repair and/or servicing, incorrect repair and/or servicing, use of wrong materials and/or incorrect spare parts 4.2. Allow the company to inspect the Goods and/or any installation and any relevant packaging as and when reasonably required by the Company. Subject to the Company being notified of any defect as is referred to in sub-clause 2 hereof within a reasonable time of it becoming apparent and subject always to the terms of sub-clause 4 hereof, the Company shall, in its option, replace or repair the defective Goods or refund a proportionate part of the Price. The Company shall have no further liability to the Customer (save as mentioned in sub-clause 6 hereof). The Company shall be liable to indemnify the Customer in respect of any claim for death or personal injury to any person in so far as such is attributable to the negligence or breach of duty of the Company or any failure by the Company to comply with the provisions of sub-clause 2 hereof. Save as provided in sub-clause 2 hereof the Company shall not be liable in respect of any claim by the Customer for costs, damages, loss or expenses (whether direct, indirect, consequential or otherwise) or indemnity in any respect howsoever arising including, but not by way of limitation, liability arising in negligence (other than pursuant to clause 6 above) that may be suffered by the Customer or any third party.

3.

4.

5.

6.

7.

Page 6

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Safety Notices
Symbols
This manual uses the following symbols to highlight specific areas important to the safe and proper use of the Generator.

A WARNING notice denotes a hazard. It calls attention to an operating procedure, process or similar, which if not correctly performed or adhered to, could cause personal injury or in the worst case death. Do not proceed beyond a WARNING notice until the indicated conditions are fully understood or met. A CAUTION notice denotes a hazard. It calls attention to an operating procedure, process or similar, which if not correctly performed or adhered to, could cause damage to the Generator or the Application. Do not proceed beyond a CAUTION notice until the indicated conditions are fully understood or met.

Caution, risk of electric shock. Ensure power to the Generator has been removed before proceeding.

Table 1 - Safety Symbols

Safety Notice to Users
These instructions must be read thoroughly and understood before installation and operation of your Peak i-Flow 50*. Use of the Generator in a manner not specified by Peak Industrial MAY impair the SAFETY provided by the equipment. When handling, operating or carrying out any maintenance, personnel must employ safe engineering practices and observe all relevant local health and safety requirements and regulations. The attention of UK users is drawn to the Health and Safety at Work Act 1974, and the Institute of Electrical Engineers regulations.

Nitrogen is not a poisonous gas, but if the concentration in the inhaled air becomes too high there will be a risk of asphyxiation.

Page 7

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Environmental Declaration
We of declare that: Equipment Model Nitrogen Gas Generator i-Flow 50* Peak Industrial Ltd. Fountain Crescent, Inchinnan. Renfrewshire PA4 9RE

Is fully compliant with the following Directives: 2002/96/EC WEEE (Waste of Electrical and Electronic Equipment)

2002/95/EC RoHS (Restriction of Hazardous Substances) Peak Scientific Instruments Ltd fully complies with its obligations towards the European WEEE (Waste of Electrical and Electronic Equipment) Directive 2002/96/EC. These obligations are being met within the B2B compliance group. Peak Scientific Instruments Ltd has developed all reasonable ‘due diligence’ controls to ensure that our products comply with the principles and requirements of the European RoHS (Restriction of Hazardous Substances) Directive 2002/95/EC. Similar directives in the United States and China, for example, have also been captured within this program. Where a specific certificate of compliance is required, this can be requested, on a product serial number basis, directly from Peak Scientific Instruments Ltd, by contacting us through our website on www.peakscientific.com

Signed By: Name: Position: Done at: Date: Chris Pugh Engineering Director Peak Scientific Instruments Ltd, Inchinnan, Scotland. 16 February 2012
th

Page 8

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Technical Specification
Environment
5010 Minimum Operating Ambient Temperature Maximum Operating Ambient Temperature* Maximum Relative Humidity 5020 5030 5040 5°C (41°F) 30°C (86°F) 70%

* Maximum safety ambient temperature 35°C ** When taken out of storage the Generator should be allowed to acclimatize at room temperature for a minimum of 3 hours before operation.

Generator Outlets
Minimum Air Inlet Pressure Maximum Air Inlet Pressure Minimum Air Inlet Flow Maximum Gas Output Pressure Maximum Pressure Drop (Outlet-Inlet) Maximum Outlet Flow (High Purity Nitrogen) Start-Up Time For Purity Particles 60 l/min 180l/min 125 psi (8.7 bar) 145 psi (9.9 bar) 360l/min 540l/min 720l/min 100 psi (6.8 bar) 8 psi (0.55 bar) 120 l/min 180 l/min 240 l/min 60 minutes 0.01 µm

Electrical Requirements
Voltage Frequency Current Fuse Input connection Power cord (Supplied) Pollution degree Installation category 100V 60Hz 0.222A S506-1.6-R C20 Plug C19 socket to local connection (13A minimum) 2 II 230V 50Hz 0.123A

General
Dimensions in cm (inches) W x D x H Weight Shipping weight Noise level 70 73 50 (19.6) x 70 (27.5) x 115 (45.2) 75 78 80 83 85 88

54 dBA @ 1m

It should be noted that the gas pressures and flows are factory set. The pressures shown on the Generator front panel are in excess of the maximum inlet pressure of the instrument. This is to allow for known pressure drops.

Page 9

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Technical Specification
Environment
5050 Minimum Operating Ambient Temperature Maximum Operating Ambient Temperature* Maximum Relative Humidity 5060 5070 5080 5°C (41°F) 30°C (86°F) 70%

* Maximum safety ambient temperature 35°C ** When taken out of storage the Generator should be allowed to acclimatize at room temperature for a minimum of 3 hours before operation.

Generator Outlets
Minimum Air Inlet Pressure Maximum Air Inlet Pressure Minimum Air Inlet Flow Maximum Gas Output Pressure Maximum Pressure Drop (Outlet-Inlet) Maximum Outlet Flow (High Purity Nitrogen) Start-Up Time For Purity Particles 300l/min 900l/min 125 psi (8.7 bar) 145 psi (9.9 bar) 1080l/min 1260l/min 1440l/min 100 psi (6.8 bar) 8 psi (0.55 bar) 360l/min 420l/min 480l/min 60 minutes 0.01 µm

Electrical Requirements
Voltage Frequency Current Fuse Input connection Power cord (Supplied) Pollution degree Installation category 100V 60Hz 0.222A S506-1.6-R C20 Plug C19 socket to local connection (13A minimum) 2 II 230V 50Hz 0.123A

General
Dimensions in cm (inches) W x D x H Weight Shipping weight Noise level 90 93 50 (19.6) x 70 (27.5) x 115 (45.2) 95 98 100 103 105 108

54 dBA @ 1m

Page 10

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Unpacking
Although Peak Industrial takes every precaution with safe transit and packaging, it is advisable to fully inspect the unit for any sign of transit damage. Check ‘SHOCKWATCH’ label for signs of rough handling prior to un-packing –

Any damage should be reported immediately to the carrier and Peak Industrial or the Peak Partner from where the unit was purchased. Follow the unpacking instructions posted on the side of the crate. It will require two people to remove the unit from the shipping crate and to manoeuvre the Generator onto the floor. Please save the product packaging for storage or future shipment of the Generator. Note: Included with the Generator is a “Fittings Kit” containing mains power leads for UK, EU and US also all the required fittings. Be careful not to discard these with the packaging.

Page 11

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Installation
Generator Environment
The Generator is designed for indoor use only. It should be installed adjacent to the instrument it is supplying. If this is not convenient then the unit can be sited elsewhere, however, consideration should be made of the lengths of pipe runs as pressure drops can result from extended runs of pipe. Please see the Tubing lengths section for further details. Performance of the Generator (like all sophisticated equipment) is affected by ambient conditions. Note should also be taken to the proximity of Air Conditioning outlets. These can sometimes give rise to “pockets” of air with high relative humidity. Operation of the unit within such a pocket could adversely affect its performance. Consideration should also be given to the air flow around the unit. It is recommended that an air gap of 75mm (3”) should be maintained down both sides, at the rear and across the top of the unit. Please refer to the drawing below for the general dimensions of the unit. Maximum Ambient Conditions: 30°C (dry bulb) 80%RH (Max) Non-Condensing

General Dimensions

The Generator must always be placed on a level surface. Failure to do so will affect the performance of the Generator.

Page 12

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Unit Controls
Power Switch N2 Pressure Gauge

Page 13

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Rear Connections
Fittings Kit
Supplied in the Fittings Kit are all the fittings required to connect the i-Flow 50* Generator to the appliance. The contents of the Fittings Kit are as follows:

Power Cord

12mm Compression (x2) (Air In & Nitrogen) 6mm Compression (x1) (Drain)

All of the Generator output ports are located on the output panel at the rear of the Generator.

Drain Connection
Fit the 6mm push fit fitting (item 2 from fittings kit) to the drain port located on the output panel. Tighten using a 16mm or 5/8” spanner. Use the 6mm tubing (item 4 from fittings kit) to connect this to a suitable drain connection or container. It should be noted that the Generator can expel a considerable amount of water from this (dependant on ambient humidity).

If a container is used it should be emptied at regular intervals. The container must NOT have an air tight seal as water and air are expelled at pressure.

Page 14

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Air Connection
The i-Flow 50* Generator should be connected to a clean, dry, oil – free source of compressed air. A minimum pressure of 125 psig is required for efficient operation of the Generator. Any doubts as to the suitability of your compressed air supply should be referred to the factory for advice. A maximum oil vapour content of 5 mg per m^3 is permissible. Air Inlet and Nitrogen Outlet connections are at the rear of the generator in the middle right side of the panel. The Air inlet connection is the left port. 1/2” BSP female, outlet port is 3/8” BSP female. The generator is supplied with two breathing air pre-filters and an activated carbon post filter, which are fitted internally. The breathing air filters will drain moisture and are equipped with automatic drains. This is connected to the 1/8” BSP Female port at the bottom of the rear panel. Any bulk moisture in the inlet air will be trapped by these filters and released through this drain port, which should be led to a convenient place.

Electrical Connection
Connect the Generator to an 85-264 VAC single-phase supply using the power cord provided. If the appropriate power cord is not supplied; a new plug, rated to at least 12 amps, can be fitted by a qualified electrician.

This unit is classified as SAFETY CLASS 1. THIS UNIT MUST BE EARTHED. Before connecting the unit to the mains supply, please check the information on the serial plate. The mains supply must be of the stated AC voltage and frequency.

EARTH/GROUND (E):LIVE (L):Neutral (N):-

Green & Yellow Brown Blue

or or or

Green Black White

Page 15

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Commissioning
With the Generator installed as described earlier, Disconnect the Nitrogen Outlet connection to allow the generator to vent to atmosphere until the unit is stabilized then open the air supply. The Generator has been pre-set in the factory to give the specified output flow-rate and pressure. Once the Membrane reaches the design pressure the Generator will stabilise and produce pure Nitrogen. Maximum purity will be achieved after around 1 hour. After this time the generator can be re-connected to the application. The design of the generator is that it will deliver up to rated output flow of Nitrogen at 100 psig. Should the demand for Nitrogen be less than the rated output flow, or indeed should the demand stop the generator will Automatically go into standby mode this will switch off inlet Air supply, and on demand of Nitrogen the pressure switch will detect and energize solenoid valve and generator will start to produce Nitrogen. The generator is protected from over pressurising.

Tubing Lengths
The diameter of the tubing which will be connected to the gas outlet is important and is determined by the length of tubing required. Failure to follow these recommendations could lead to pressure between generator and application. 10 - 40 meters: > 40 metres: Use 6/4 (6mm O/D, 4mm I/D) P.T.F.E. tubing. Use 10/8 (10mm O/D, 8mm I/D). Tubing and fittings not supplied in the fittings kit. Please contact Peak Industrial with the relevant distance and we will calculate the flow resistance and the tubing size required.

A combination of 6/4 and 10/8 tubing may be used to ensure that there is no large diameter tubing within the lab (i.e. for the first 20 meters from the Generator use 10/8 and the final 10 meters to the Instrument use 6/4 tubing). Keep the connections and bends to a minimum. The imperial equivalents are: 6/4 = 1/4” O/D, 3/16” I/D. 10/8 = 3/8” O/D, 5/16” I/D

Page 16

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
IMPORTANT DOCUMENTS Warranty Entitlement
To register your generator for your warranty entitlement, send the completed form to Peak Scientific by: • • • • Email Online Phone Fax
warranty@peakscientific.com http:/ /www.peakscientific.com/service-and-support/warranty_registration

+44 (0)141 530 4185 +44 (0)141 812 8200

PRODUCT WARRANTY REGISTRATION
COMPANY: ADDRESS: EMAIL ADDRESS: CONTACT NAME:

CITY/TOWN: POSTCODE: COUNTRY: TELEPHONE:

GENERATOR SERIAL NUMBER:

MODEL TYPE: INSTALLATION DATE (DD/MM/YYYY):

Important Please Note:
You have 1 month to register you Peak Scientific product from the date of shipment. If you wish to defer installation of your generator you must notify Peak Scientific within 1 month of the shipment date. This can be done by emailing warranty@peakscientific.com Once registered the warranty will be honoured for a period of 12 months after the installation date. For any generators that remain unregistered the warranty will begin from date of shipment. Thank you on behalf of Peak Scientific.

Page 17

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Normal Operation
The i-Flow 50* Gas Generator is designed specifically to minimize operator involvement. Given that the system is installed as described in earlier sections and is serviced in accordance with the specified maintenance recommendations (see Service Requirements), then it should simply be a matter of turning the Generator on when it is required. The Generator will automatically produce the factory set flow and pressure as detailed in the Technical Specifications.

On Demand Gas
Each individual system produces gas on demand. If the instrument is operating and requires a gas flow, the selected system will supply this to suit the requirements of the instrument. If the instrument requirement for gas stops, the system will also stop, once it has reached its upper set limit in the internal storage tanks. If the demand from the instrument starts again, the system will detect the demand for gas and will automatically start again to suit the demand.

Cleaning
Clean the outside of the Generator only using warm soapy water and a clean damp cloth. Ensure the cloth is thoroughly rung out to remove excess fluid prior to use. Cleaning should only be undertaken with the power switched off and the power cord removed from the rear of the Generator.

Under no circumstances should any solvents or abrasive cleaning solutions be used as these can contain fumes that could be harmful to the Generator.

Page 18

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Service Requirements
Servicing and/or repair of the Generator should only be undertaken by a TECHNICALLY COMPETENT PERSON with the Generator in a safely isolated condition.

Due to the simplicity of the design and the small number of moving parts the iFlow 50* Nitrogen Generators will have a long and trouble free life. However as with all scientific and technical equipment it should be regularly inspected and serviced as below.

Service Schedule
Service interval 12 months Component Element Active Carbon Element 0.01 micron RAC Filter Element Part No. 00-0043 00-0042 00-0041 Qty. 1 1 1

As an alternative to purchasing the 12 month service items individually an Annual Service Kit is available as one part number. This contains all the filters required for this Generator. Purchase Interval 12 months Component Annual Service Kit Part No. 08-4429 Qty. 1

Safely Isolated Condition
The unit is in a safely isolated condition when it is disconnected from its application and fully de-pressurised. Directions for isolating the Generator are shown below. Failure to place the Generator in a safely isolated condition when instructed to do so may lead to personal injury or injury to others and even death. a) Switch generator off. b) Disconnect from air supply. c) Ensure the output pressure gauge reads zero. (If gauge does not fall to zero, loosen the outlet fitting slightly to allow trapped gas to escape). Disconnect from the application.

Page 19

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Safe State After Repair
To guarantee the generator is in a safe state after a repair, please ensure the following conditions are met; • All earth leads have been reconnected.
Earth leads should be connected to the earth tabs located on the door panels, as shown below.



The electricity cable has been correctly refitted.
The mains cable should be plugged into the IEC power inlet located on the rear panel of the generator. This unit is classified as SAFETY CLASS 1. THIS UNIT MUST BE EARTHED.

Page 20

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Product Overview
BA Filter RAC Filter N2 Membrane

Pressure Gauge

Pressure Switch

Pressure Regulator

Flow Controller

Page 21

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Breathing Air Filter Element Replacement
Ensure that Generator is in Safely Isolated Condition

1.

Remove 6mm drain tubing from push-fit stud situated on under-side of the bowl.

2. Remove the top and bottom filter bowls by turning the bowl clockwise and anti-clockwise respectively.

3. Remove the filter element by pulling it away from the filter assembly.

4. Fit the replacement elements.

5. Re-fit the filter bowls.

00-0043

00-0042

Page 22

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
RAC Filter Element Replacement
Ensure that Generator is in Safely Isolated Condition

1.

Open the filter bowl valve to ensure it is depressurised.

2. Remove the filter bowl by turning it as shown to reveal the RAC filter element Part number 00-0041. a. For easier access, the filter assembly can be removed from the cabinet by removing the 4 of nyloc nuts and disconnecting the tubing. 3. Remove and replace the filter element and re-assemble.

00-0041

Page 23

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Pressure Switch
Accessing the electrical panel without safely isolating the Generator should only be carried out by trained service personnel

Overview
1. Electrical Connection

1 2 3

2. LED Display 3. Edit Button 4. Connection for Pressurised Air 4

Pressure Settings
NM32LA Pressure Settings Pressure Limit Upper Lower Pressure (PSI) 115 105

Table 2: NM32LA Pressure Settings

Procedure to set Pressure Switch
1. Close off the pressure regulator in the generator

2. Attach the external pressure regulator and valve assembly between the house air supply and the AIR IN port on the generator. Ensure the valve is in the closed position. 3. Connect the power cable to the generator and switch on the power. 4. On the house air regulator set the supply pressure as per the requirements listed in the Technical Specification of this manual. 5. Slowly release the house air supply to pressurise the tank. 6. When the internal gauge reads the required upper limit shown in the table above press the set button on the pressure switch, the LED will start to flash. 7. Close the shut off valve on the air supply in to the generator.

Page 24

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
8. Gradually open the pressure regulator in the generator unit to reduce the tank pressure to the lower limit shown in the table above and press the button on the pressure switch to set the lower limit. The LED goes off.

Care should be taken so as to not over pressurise tanks

Page 25

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
Trouble Shooting
Problem Possible Solution • Ensure the power cord is plugged into the generator and that the power socket is turned on. • Check the fuse in the power cord plug. • Contact your service provider. • Disconnect the power cord from the rear of the unit. • Replace the fuse, reconnect the power cord. • Contact your service provider.

The Generator will not switch on & the power switch does not illuminate.

The generator will not switch on but the power switch is illuminated.

Page 26

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
i-Flow 5010 Pneumatic Schematic Rev 1

Page 27

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
i-Flow 5020 Pneumatic Schematic Rev 2

Page 28

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
i-Flow 5030 Pneumatic Schematic Rev 1

Page 29

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
i-Flow 5040 Pneumatic Schematic Rev 1

Page 30

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
i-Flow 5050 Pneumatic Schematic Rev 1

Page 31

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
i-Flow 5060 Pneumatic Schematic Rev 1

Page 32

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
i-Flow 5070 Pneumatic Schematic Rev 1

Page 33

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
i-Flow 5080 Pneumatic Schematic Rev 1

Page 34

2014 © Peak Industrial - Rev. 1 - 16/04/14

i-Flow 50* User Manual
i-Flow Electrical Schematic Rev 1

Page 35

2014 © Peak Industrial - Rev. 1 - 16/04/14

Peak Scientific UK Fountain Crescent Inchinnan Business Park Inchinnan PA4 9RE Scotland, UK Tel: +44 (0)141 812 8100 Fax: +44 (0)141 812 8200 Peak Scientific Germany Herriotstrasse 1 60528 Frankfurt

Peak Scientific North America 19 Sterling Road Suite #1 Billerica, MA 01862 USA Tel: +1 866 647 1649 Fax: +1 978 608 9503 Peak Scientific China Room 606 Building 1 Lane 2277 Zuchongzhi Road Pudong New Area Shanghai 201203, China Tel: +86 21 5079 1190 Fax: +86 21 5079 1191 Peak Scientific Brazil Peak Scientific Brasil Av. Quieroz Filho 1700 – torre Sunny-Conj. 602 São Paulo SP Brasil Tel: +1 866 647 1649

Peak Scientific India 202, Amsri Shamira Old Lancer Line Opp. St. Mary’s Degree College S.D. Road Secunderabad 500 025, India Tel: +91 40 2780 0663 Fax: +91 40 2780 0663 Peak Scientific Mexico Solon 352 Col. Los Morales Polanco 11530 Mexico, D.F. Mexico Tel: Fax: +1 866 647 1649 +1 978 608 9503

Peak Scientific Africa PO Box 478 Somerset Mall 7137 South Africa Tel: +27 (0)2185 16542 Fax: +27 (0)8654 64473 Peak Scientific Australia PO Box 65 Belmont Victoria 3216 Australia Tel: +61 1300 965 352

Germany Tel: +49 (0)69 677 33 490 Fax: +49 (0)69 677 33 200 Peak Scientific Taiwan 4F.-6, No.736 Zhongzheng Rd. Zhonghe Dist. New Taipei City Tel: +886 2 8226 2383 Fax: +886 2 8226 9499

Peak Scientific Japan K.K. 2-7-56, 2F Fuji Building 28 Kita Aoyama, Minato-Ku Tokyo, Japan 107-0061 Tel: +81 3-6864-0468

Peak Scientific Singapore 3 Science Park Drive #03-14 The Franklin Science Park Drive 1 Singapore, 118223 Tel: +65-6777 1966 Fax: +65-6777 1978

2014 © Peak Industrial - Rev. 1 - 16/04/14

Search for similar resources

Remove