TOC 1500 HP - Installation Guide 

Resource downloads

File information File dimensions File size Options

Original PDF File

1.8 MB Download

Screen

566 × 800 pixels (0.45 MP)

4.8 cm × 6.8 cm @ 300 PPI

37 KB Download

Preview

Full screen preview

37 KB View
Resource details

Resource ID

2810

Access

Open

Contributed by

Liam Couttie

Updated date

29 November 18

Review date

29 November 19

Title

TOC 1500 HP - Installation Guide

Revision Number

1

Revision Details

Initial Release - LC

Keywords

TOC, TOC1500HP, 1500, HP, 1500HP, Install, Installation, Guide, Manual

Product Range

Other

Language

UK English

Company Brand

Peak Scientific

Public / Private

public

Extracted text

TOC 1500 HP
Installation Guide

Copyright © Peak Scientific Instruments Ltd 2018 — TOC 1500 HP Installation Guide Rev 1 PN IG-0026 RSID 2810 —03/12/2018

Change History
Rev

Comment

Name

Date

How to use this Installation Guide
This document is intended to be used only as a Quick Start Guide, to facilitate safe and
correct installation and initial configuration of your Peak Scientific gas generator.
For more extensive user operation directions, we recommend you download the User
Manual from the website.

Please visit www.peakscientific.com/downloads to
download the full User Manual for your gas generator.
Thank you for selecting Peak Scientific to meet your laboratory gas generation needs,
and should you require any further assistance or support please do not hesitate to
contact Peak Scientific or Peak Partner from which you purchased your generator.

Page 2

Safety Notices
Peak Scientific Instruments cannot anticipate every possible circumstance which may
represent a potential hazard. The warnings detailed within this document detail the
most known potential hazards, but by definition cannot be all inclusive. If the user
employs an operating procedure, item of equipment or a method of working which
is not specifically recommended by Peak Scientific, the user must ensure that the
equipment will not be damaged or become hazardous to persons or property.

Symbols
This document uses the following symbols to highlight specific areas important to the
safe and proper use of the Generator

WARNING

A WARNING notice denotes a hazard. It calls attention to an operating procedure,
process or similar, which if not correctly performed or adhered to, could cause
personal injury or in the worst case death. Do not proceed beyond a WARNING
notice until the indicated conditions are fully understood or met.

CAUTION

A CAUTION notice denotes a hazard. It calls attention to an operating procedure,
process or similar, which if not correctly performed or adhered to, could cause
damage to the Generator or the Application. Do not proceed beyond a CAUTION
notice until the indicated conditions are fully understood or met.
Caution, risk of electric shock. Ensure power to the Generator has been removed
before proceeding.

Safety Notice to Users

WARNING

WARNING

These instructions must be read thoroughly and understood before
installation and operation of your Peak Generator. Use of the generator
in a manner not specified by Peak Scientific MAY impair the SAFETY
provided by the equipment.
When handling, operating or carrying out any maintenance, personnel
must employ safe engineering practices and observe all relevant local
health and safety requirements and regulations. The attention of UK
users is drawn to the Health and Safety at Work Act 1974, and the
Institute of Electrical Engineers regulations.
If the equipment is used in a manner not specified by the manufacturer,
the protection provided by the equipment may be impaired.

WARNING

Page 3

Fittings Kit

x1

US Mains Cable C13 6-15 04-1029

x3m

6mm PE Tubing 00-1282

x1

US Mains Cable C13 5-15 04-1039

2x3m

6mm OD Teflon 00-1302

x1

1/4” - 6mm Push Fit Elbow Fitting 02-4331

x1

x2

EU Mains Cable C13 04-1038
Page 4

x4

UK Mains Cable C13 04-1028

10A Fuse 00-1208

1.
WARNING



Unpack the generator from the shipping crate and position on a flat surface, in
desired area.
WARNING the weight of the unit constitutes a two man lift. Safe lifting practices are
advised.

2.

02-4431

Select two of the 1/4” - 6mm Push Fit Elbow Fittings 02-4331 and attach them to the
Inlet and Drain ports at the left side of the generator. It is recommended that PTFE tape
is applied to the threads to ensure a leak-tight fit.
Page 5

3.

00-1302

00-1282
Attach the supplied 6mm OD Teflon 00-1302 and connect this to the 1/4” - 6mm
Push Fit Elbow Fitting 02-4331 on the Inlet port. Attach the supplied
Connect the 6mm PE Tubing 00-1282 to the 1/4” - 6mm Push Fit Elbow Fitting
02-4331 on the Drain port. Fit the other end of the tubing to a suitable drain
connection or container. The container MUST NOT have an airtight seal as water and
air will be expelled periodically under a slight pressure.

4.

02-4431

Select a 1/4” - 6mm Push Fit Elbow Fitting 02-4331 and attach it to the Outlet port on the
right side of the generator. It is recommended that PTFE tape is applied to the threads to
ensure a leak-tight fit.
Page 6

5.

00-1302

Fit 6mm OD Teflon 00-1302 tubing to the 1/4” - 6mm Push Fit Elbow Fitting 02-4331
on the generator Outlet port.
Connect the other end of each section of tubing to your instruments gas input.

6.

04-1028/04-1029/
04-1038/04-1039

Select the appropriate mains cable from the fittings kit and plug the IEC 60320/C19
cable into the mains input at the side of the generator.

Page 7

7.
UK

EU

US
110V

US
230V

CAUTION

Plug the mains cable into the corresponding 110VAC 60Hz OR 230VAC 50/60Hz
single phase power supply.
CAUTION ensure the correct cable has been selected for your electrical supply.
Consult the Electrical Requirements section if you are unsure of the requirements of
your generator.

8.

Swith the generator ON, using the switch at the side of the generator.

Page 8

9.

Allow the generator to run until the Temperature display reads 400°C.

10.

/
CONGRATULATIONS

Your Peak Scientific gas generator is now fully installed, operational and ready to
supply gas on demand to your instrument.
Page 9

General Notes

The Teflon tube supplied in the fittings kit is to allow the generator to be installed
adjacent to the instrument it is supplying. If the generator is to be installed further
away from the instrument then attention needs to be paid to pressure drops that could
occur. The maximum distance away from the instrument the generator can be placed
still using 6mm (4mm internal diameter) or ¼” (3/16” internal diameter) tubing is 10m.
For further information relating to tubing lengths please refer to the user manual.
1.

Electrical Requirements
Generator
TOC 1500 HP

Voltage
230

110

Frequency
50
60









Plug Type
UK, EU, US 230V,
US 110V

Please familiarise yourself with the full User Manual available at www.peakscientific.
com/downloads. This includes all other technical specifications, operating
instructions, service requirements, contact details and trouble shooting.

Page 10

Go Online or Complete and Return
We know that registering any of your recently purchased products is not the
first thing on your mind- but it is very important to both of us. Not all warranties
are alike and Peak Scientific stand out against other gas suppliers as we offer a
comprehensive, quick response, on-site warranty. This means that in the very
unlikely case that your gas generator develops a fault we have rapid support
teams on-hand around the world who are able to come to your lab and get you
back up and running in no time.
Register for your comprehensive 12 month on-site warranty with ease online at
www.peakscientific.com/register.
Alternatively, you can send the completed form to Peak Scientific by post or
email at warranty@peakscientific.com.

Go Online or Complete and Return
You can register for your FREE 12 month Warranty with ease online at
www.peakscientific/protected.
Alternatively, you can send the completed form to Peak Scientific by post or
email at warranty@peakscientific.com.

Product Warranty Registration
Contact name
Email address
Company
Address
City/town
Postcode
Country
Telephone
Generator serial #
Model type
Installation date
Do you still use an
alternative gas solution i.e.
cylinders or bulk liquid?

Yes

What gas requirements do
you have in your lab?

Hydrogen

No

Nitrogen

Zero Air

Extend your cover with
Peak Scientific offer comprehensive gas generator after sales support packages.
Peak [Protected] aftercare support can guarantee an on-site response within
72 hours*, genuine parts from our ISO9001 approved factory and a 95% first-time
fix rate. See our enclosed Peak [Protected] leaflet for further information.
Important!
You have 1 month to register your Peak Scientific product from the date of installation. Once registered
the warranty will be honoured for a period of 12 months. If you wish to defer the installation of your
generator, you must notify Peak Scientific immediately by emailing warranty@peakscientific.com.
For generators that remain unregistered after 1 month from the shipment date, the warranty will be
considered active from the date of factory dispatch.
* Complete Plan only






Important!
You have 1 month to register your Peak Scientific product from the date of
installation. Once registered the warranty will be honoured for a period of 12
months. If you wish to defer the installation of your generator, you must notify
Peak Scientific immediately by emailing warranty@peakscientific.com. For
generators that remain unregistered after 1 month from the shipment date, the
warranty will be considered active from the date of factory dispatch.
Page 11

Please visit www.peakscientific.com/downloads to
download the full User Manual for your gas generator.

Peak Scientific has highly trained, fully certified Field Service Engineers located in over 20 countries
across every continent around the world. This allows us to provide an industry-leading rapid response
service to our customers. With [Peak Protected], your laboratory’s productivity becomes our top
priority.
To discuss Peak Protected generator cover and payment options speak to your local Peak
Representative or for further information contact: protected@peakscientific.com.

Peak Scientific
Fountain Crescent
Inchinnan Business Park
Inchinnan
PA4 9RE
Scotland, UK
Tel: +44 141 812 8100
Fax: +44 141 812 8200
For further information on any of our
generator products please contact
discover@peakscientific.com

Copyright © Peak Scientific Instruments Ltd 2018 — TOC 1500 HP Installation Guide Rev 1 PN IG-0026 RSID 2810 —03/12/2018

Search for similar resources

Remove