06-3200 Dual Tap Transformer - Installation Guide 

Resource downloads

File information File dimensions File size Options

Original PDF File

1.4 MB Download

Screen

566 × 800 pixels (0.45 MP)

4.8 cm × 6.8 cm @ 300 PPI

95 KB Download

Preview

Full screen preview

95 KB View
Resource details

Resource ID

268

Access

Open

Contributed by

Liam Couttie

Updated date

-

Review date

03 May 19

Title

06-3200 Dual Tap Transformer - Installation Guide

Revision Number

4

Keywords

Installation, Guide

Product Range

Other

Language

UK English

Company Brand

Peak Scientific

Public / Private

public

Reviewed on 3rd May 2017 - LC

Extracted text

Installation Guide
06-3200 Dual Tap Transformer 200V – 230V
For ABN2ZA, AB3G, NM3G, NM60LA, NM32LA (All models) & All Genius 10 Series Generators

INSTALLATION
1.

2.

Remove the transformer from all
the packaging, ensuring that the
two securing screws are retained
and not thrown away.

3.

Ensure that the generator to
which the transformer is to
be fitted is switched OFF on
the front panel.

4.

Remove the mains
cable from the mains
supply socket.

5.

Once safely disconnected from the
mains, remove the generator side panel.
Model ABN2ZA, NM32LA, 10 Series –
LH side
Model AB-3G, NM-3G, NM60LA – RH
side

Fountain Crescent
Inchinnan Business Park
Inchinnan, PA4 9RE
Scotland, UK

6.

Using the Hex-Key
provided in the
fittings kit, turn the
lock 90o clockwise.

Remove the panel from the
generator.
An earth lead is connected
to the inside of the panel.
This can be removed by
pulling it off the spade
connector on the door.

T: +44 (0)141 812 8100
F: +44 (0)141 812 8200
W: www.peakscientific.com
E: info@peakscientific.com

Part No. IG-06-3200
Rev.
4
Page

Page 1 of 5

7.

8.

9.

ATTENTION
Do not touch anything
inside the generator while
the side panels are
removed and the mains
power is connected to the
unit.

Plug the mains cable into
an appropriate 230VAC
50/60Hz single phase
power supply

10a.

10b.

ABN2ZA
NM32LA
10 Series

The voltmeter is located on the underside of
the compressor area (ABN2ZA, NM32LA, 10
Series). This will measure and display the
mains voltage that is being supplied to the
generator. Note the displayed voltage.

>=220
>=194

Switch the generator power ON
at the switch on the front panel.

AB-3G
NM-3G
NM60LA

The voltmeter is located on the bottom of the
electrical panel (AB-3G, NM-3G, NM60LA).
This will measure and display the mains
voltage that is being supplied to the
generator. Note the displayed voltage.

=

If the voltmeter reads a voltage of between 220V and
253V the mains supply is sufficient and the transformer
should not be fitted.

=

If the voltmeter reads a voltage between 194V and
219V then the transformer is required. Proceed with
the installation of the transformer.
Fountain Crescent
Inchinnan Business Park
Inchinnan, PA4 9RE
Scotland, UK

T: +44 (0)141 812 8100
F: +44 (0)141 812 8200
W: www.peakscientific.com
E: info@peakscientific.com

Part No. IG-06-3200
Rev.
4
Page

Page 2 of 5

11.

12.

Switch the generator power OFF at the
switch on the front panel.

Remove the mains cable completely from the
power supply and then unplug from the rear
of the generator.

**NOTE**
The transformer has a ‘Dual Tap’ facility. This allows it to cover a broarder range of low
supply voltages. The transformer will be supplied with the 200V tap already connected. This
will be required for most applications.
If the additional 208V tap is required, then this can be easily changed before connecting to
the generator.
Voltage Reading

197V to 212V
Voltage Reading

213V to 219V

The 200V tap is required, no modification to the
transformer is necessary. Progress to stage 16.
The 208V tap is required. It is necessary to change the tap
inside the transformer. This is very easy and can be done
by following stage 13. to stage 15.

13.

14.

Place the transformer on its back and
remove the cover retaining screw using
either a flat blade screwdriver or ¼”
spanner. The cover can then be removed.

Fountain Crescent
Inchinnan Business Park
Inchinnan, PA4 9RE
Scotland, UK

The ‘Primary Taps’ are now exposed. These
are clearly labelled ‘200V’ and ‘208V’. To
change the tap simply pull the connector
labelled ‘200V’ off the spade terminal and
push the connector labelled ‘208V’ fully on to
the terminal. The ‘200V’ tap wire removed can
be safely left loose in the compartment.
T: +44 (0)141 812 8100
F: +44 (0)141 812 8200
W: www.peakscientific.com
E: info@peakscientific.com

Part No. IG-06-3200
Rev.
4
Page

Page 3 of 5

15.

16.

Replace the transformer cover and securly
fasten with the retaining screw. The
transformer is now ready for mounting on
the rear of the generator.

17.

The mounting screws provided can be
screwed into the holes on the rear of the
generator. Leave approvimately 5mm
protruding. The transformer can then be hung
on the protruding screws. Once located
correctly the screws can be fully secured.

18.

Plug the mains cable from the transformer,
labelled ‘TO GENERATOR’ into the mains
socket on the rear of the generator.

19.

Plug the original generator mains cable into
the mains inlet socket on the transformer,
labelled ‘MAINS INPUT’.

20.

Plug the mains cable back into the original
single phase mains power supply and
ensure the power is switched ON.

Fountain Crescent
Inchinnan Business Park
Inchinnan, PA4 9RE
Scotland, UK

Switch the generator ON again at the switch
on the front panel.

T: +44 (0)141 812 8100
F: +44 (0)141 812 8200
W: www.peakscientific.com
E: info@peakscientific.com

Part No. IG-06-3200
Rev.
4
Page

Page 4 of 5

21.

22.

The voltmeter should now read above
220V. If it is still below 220V and you have
not fitted the ‘208V tap’, disconnect the
transformer and return to stage 13.

23.

Switch the generator OFF on the front panel
and disconnect from the mains supply.

24.

Re-attach the side panel to the generator,
taking care to ensure the earth lead is
reconnected correctly. The locks are
secured by turning the lock 90o
anticlockwise using the hex key provided.

Once the side panel is securely assembled,
the mains power supply can be reconnected
and the generator switched back ON.

CONGRATULATIONS
You have now successfully installed the transformer on your PEAK SCIENTIFIC gas
generator. The generator is now operational and ready to supply gas on demand to your
instrument.
If you should have any problems or require further support please contact our Technical
Helpdesk on the following numbers
Europe (ROW)
+44 (0)141 530 4180

North America
+1 866 732 5427

India
+91 (0)40 2780 0663

support@peakscientific.com

usasupport@peakscientific.com

indiasupport@peakscientific.com

Fountain Crescent
Inchinnan Business Park
Inchinnan, PA4 9RE
Scotland, UK

T: +44 (0)141 812 8100
F: +44 (0)141 812 8200
W: www.peakscientific.com
E: info@peakscientific.com

Part No. IG-06-3200
Rev.
4
Page

Page 5 of 5

Search for similar resources

Remove