Infinity XE 50 Series - Installation Guide 

Resource downloads

File information File dimensions File size Options

Original PDF File

1.4 MB Download

Screen

566 × 800 pixels (0.45 MP)

4.8 cm × 6.8 cm @ 300 PPI

46 KB Download

Preview

Full screen preview

46 KB View
Resource details

Resource ID

2028

Access

Open

Contributed by

Liam Couttie

Updated date

06 June 18

Review date

03 July 19

Title

Infinity XE 50 Series - Installation Guide

Revision Number

2

Revision Details

Additional Models Added - LC

Keywords

Infinity, XE, 50 Series, fifty, 5011, 5021, 5031, 5041, 5010, 5020, 5030, 5040, Installation, Guide, Install

Product Range

Infinity

Language

UK English

Company Brand

Peak Scientific

Public / Private

public

Extracted text

Infinity XE 50 Series (All Models)
Installation Guide

Copyright © Peak Scientific Instruments Ltd 2017 — Infinity XE 50 Series Installation Guide Rev 2 PN UM-0019 RSID 2028 EN —05/12/2017

Change History
Rev

Comment

Name

Date

2

Further models added

Liam Couttie

28/11/2017

How to use this Installation Guide
This document is intended to be used only as a Quick Start Guide, to facilitate safe and
correct installation and initial configuration of your Peak Scientific gas generator.
For more extensive user operation directions, we recommend you download the User
Manual from the website.

Please visit www.peakscientific.com/downloads to
download the full User Manual for your gas generator.
Thank you for selecting Peak Scientific to meet your laboratory gas generation needs,
and should you require any further assistance or support please do not hesitate to
contact Peak Scientific or Peak Partner from which you purchased your generator.

Page 2

Safety Notices
Peak Scientific Instruments cannot anticipate every possible circumstance which may
represent a potential hazard. The warnings detailed within this document detail the
most known potential hazards, but by definition cannot be all inclusive. If the user
employs an operating procedure, item of equipment or a method of working which
is not specifically recommended by Peak Scientific, the user must ensure that the
equipment will not be damaged or become hazardous to persons or property.

Symbols
This document uses the following symbols to highlight specific areas important to the
safe and proper use of the Generator

WARNING

A WARNING notice denotes a hazard. It calls attention to an operating procedure,
process or similar, which if not correctly performed or adhered to, could cause
personal injury or in the worst case death. Do not proceed beyond a WARNING
notice until the indicated conditions are fully understood or met.

CAUTION

A CAUTION notice denotes a hazard. It calls attention to an operating procedure,
process or similar, which if not correctly performed or adhered to, could cause
damage to the Generator or the Application. Do not proceed beyond a CAUTION
notice until the indicated conditions are fully understood or met.
Caution, risk of electric shock. Ensure power to the Generator has been removed
before proceeding.

Safety Notice to Users

WARNING

WARNING

These instructions must be read thoroughly and understood before
installation and operation of your Peak Generator. Use of the generator
in a manner not specified by Peak Scientific MAY impair the SAFETY
provided by the equipment.
When handling, operating or carrying out any maintenance, personnel
must employ safe engineering practices and observe all relevant local
health and safety requirements and regulations. The attention of UK
users is drawn to the Health and Safety at Work Act 1974, and the
Institute of Electrical Engineers regulations.
If the equipment is used in a manner not specified by the manufacturer,
the protection provided by the equipment may be impaired.

WARNING

Page 3

Fittings Kit

x1

US Mains Cable 230V C19 6-15 04-1024

x1

x1

8mm Hex Key 00-0007

4mm Hex Key 3300407

x1

1/4” Tee Fitting 02-1048

x1

UK Mains Cable C19 04-1025

x1

5mm Hex Key 3300408

x6m

12mm OD x 10mm ID PE 00-1267

x1

EU Mains Cable C19 04-1026

x1

US Mains Cable 110V C19 5-15 04-1035

x1

Shut-Off Valve 02-4471

x2*

1/4” - 12mm Push Fit Fitting
02-5801

x1
x1

JP Mains Cable 100V C19 04-1004
Page 4

x3m

6mm OD x 4mm ID PE 00-1282

x1**

16mm Push Fit Fitting 3301060

1/4” - 6mm Push Fit Fitting
02-4600
* x1 with 5030, 5031, 5040 & 5041
** only 5030, 5031, 5040 & 5041

1. Infinity 5010,5011,5020 & 5021
For Installation of Infinity 5030,5031,5040 & 5041 please turn to page 10.

Unpack the generator from the shipping crate and position on a flat surface, in
desired area.
An Infinity XE 5011 has been used for the purposes of this Installation Guide.

2.

02-4600

02-5801

Select one of the 12mm Push-Fit Fittings 02-5801 from the fittings kit and attach to
the Air Inlet port at the rear of the generator.
Then fit the 6mm Push-Fit Fitting 02-4600 to the Drain port.
Page 5

3.

02-4471

02-5801

02-1048
Select the Tee Fitting 02-1048 and attach this to the Nitrogen port.
Next, attach the Shut-Off Valve 02-4471 to the vertical female port on the Tee Fitting,
ensuring PTFE tape is used for tight fit.
Finally attach the second 12mm Push-Fit Fittings 02-5801 from the fittings kit to the
remaining female port on the Tee Fitting, again ensuring PTFE tape is used.

4.

00-1267

00-1282

Connect the 6mm PE Tubing 00-1282 to the ¼”- 6mm Push Fit Fitting 02-4600.
Fit the other end of the tubing to a suitable drain connection or container. The container MUST
NOT have an airtight seal as water and air will be expelled periodically under a slight pressure.
Attach 3m of 12mm PE Tubing 00-1267 to the fitting attached to the fittings on the
Nitrogen port and connect to the gas inlet of your instrument. Lastly connect the rest of
the 12mm PE Tubing 00-1267 to the fittings on the Air Inlet port and connect the other
end to your air supply.
Page 6

5.

04-1004/04-1024/04-1025/04-1026/04-1035
Select the appropriate mains cable from the fittings kit and plug the IEC 60320/C19
cable into the mains input at the rear of the generator.

6.
UK

EU

US
110V
JP
100V

CAUTION

US
230V

Plug the mains cable into the corresponding 100/110/230VAC 50/60Hz single phase
power supply.
CAUTION ensure the correct cable has been selected for your electrical supply.
Consult the Electrical Requirements section if you are unsure of the requirements of
your generator.
Page 7

7.

Switch the generator power ON using the switch on the rear panel.

8.

The Inlet pressure gauge on the front of the generator will gradually increase from
0psi to the delivered inlet pressure as the system pressurises

Page 8

9.

Set the desired Nitrogen output pressure using the pressure regulator at the
rear of the generator. View the Outlet pressure gauge on front of generator
when setting the pressure.

10.

/
CONGRATULATIONS
Your Peak Scientific gas generator is now fully installed, operational and ready to
supply gas on demand to your instrument.
Page 9

1. Infinity 5030,5031,5040 & 5041

Unpack the generator from the shipping crate and position on a flat surface, in
desired area.
An Infinity XE 5030 has been used for the purposes of this Installation Guide.

2.

02-4600

3301060

Select the 16mm Push Fit Fitting 3301060 from the fittings kit and attach to the Air
Inlet port at the rear of the generator.
Then fit the 6mm Push-Fit Fitting 02-4600 to the Drain port.
Page 10

3.
02-4471

02-5801

02-1048
Select the Tee Fitting 02-1048 and attach this to the Nitrogen port.
Next, attach the Shut-Off Valve 02-4471 to the vertical female port on the Tee Fitting,
ensuring PTFE tape is used for tight fit.
Finally attach the 12mm Push-Fit Fitting 02-5801 from the fittings kit to the remaining
female port on the Tee Fitting, again ensuring PTFE tape is used.

4.

00-1267

00-1282
Connect the 6mm PE Tubing 00-1282 to the ¼”- 6mm Push Fit Fitting 02-4600.
Fit the other end of the tubing to a suitable drain connection or container. The container MUST
NOT have an airtight seal as water and air will be expelled periodically under a slight pressure.
Attach 3m of 12mm PE Tubing 00-1267 to the fitting attached to the fittings on the
Nitrogen port and connect to the gas inlet of your instrument.
Lastly connect appropriate 16mm tubing (not supplied) to the fitting on the Air Inlet port
and connect the other end to your air supply.
Page 11

5.

04-1004/04-1024/04-1025/04-1026/04-1035
Select the appropriate mains cable from the fittings kit and plug the IEC 60320/C19
cable into the mains input at the rear of the generator.

6.
UK

EU

US
110V
JP
100V

CAUTION

US
230V

Plug the mains cable into the corresponding 100/110/230VAC 50/60Hz single phase
power supply.
CAUTION ensure the correct cable has been selected for your electrical supply.
Consult the Electrical Requirements section if you are unsure of the requirements of
your generator.
Page 12

7.

Switch the generator power ON using the switch on the rear panel.

8.

The Inlet pressure gauge on the front of the generator will gradually increase from
0psi to the delivered inlet pressure as the system pressurises

Page 13

9.

Set the desired Nitrogen output pressure using the pressure regulator at the
rear of the generator. View the Outlet pressure gauge on front of generator
when setting the pressure.

10.

/
CONGRATULATIONS
Your Peak Scientific gas generator is now fully installed, operational and ready to
supply gas on demand to your instrument.
Page 14

General Notes

Electrical requirements for 230V generators are 195V - 253V 50/60Hz. For 195V 219V a 06-3200 Dual Tap Transformer is required.
1.



Electrical requirements for the 110V generator is 100V to 127V at 60 Hz.

2.

Electrical Requirements
230

Voltage
110

100

Frequency
50
60

Infinity XE 50*0











UK, EU, US 230V

Infinity XE 50*1











UK, EU, US 230V

Generator

Plug Type

Please familiarise yourself with the full User Manual available at www.peakscientific.
com/downloads. This includes all other technical specifications, operating
instructions, service requirements, contact details and trouble shooting.

Page 15

Go Online or Complete and Return
We know that registering any of your recently purchased products is not the
first thing on your mind- but it is very important to both of us. Not all warranties
are alike and Peak Scientific stand out against other gas suppliers as we offer a
comprehensive, quick response, on-site warranty. This means that in the very
unlikely case that your gas generator develops a fault we have rapid support
teams on-hand around the world who are able to come to your lab and get you
back up and running in no time.
Register for your comprehensive 12 month on-site warranty with ease online at
www.peakscientific.com/register.
Alternatively, you can send the completed form to Peak Scientific by post or
email at warranty@peakscientific.com.

Go Online or Complete and Return
You can register for your FREE 12 month Warranty with ease online at
www.peakscientific/protected.
Alternatively, you can send the completed form to Peak Scientific by post or
email at warranty@peakscientific.com.

Product Warranty Registration
Contact name
Email address
Company
Address
City/town
Postcode
Country
Telephone
Generator serial #
Model type
Installation date
Do you still use an
alternative gas solution i.e.
cylinders or bulk liquid?

Yes

What gas requirements do
you have in your lab?

Hydrogen

No

Nitrogen

Zero Air

Extend your cover with
Peak Scientific offer comprehensive gas generator after sales support packages.
Peak [Protected] aftercare support can guarantee an on-site response within
72 hours*, genuine parts from our ISO9001 approved factory and a 95% first-time
fix rate. See our enclosed Peak [Protected] leaflet for further information.
Important!
You have 1 month to register your Peak Scientific product from the date of installation. Once registered
the warranty will be honoured for a period of 12 months. If you wish to defer the installation of your
generator, you must notify Peak Scientific immediately by emailing warranty@peakscientific.com.
For generators that remain unregistered after 1 month from the shipment date, the warranty will be
considered active from the date of factory dispatch.
* Complete Plan only






Important!
You have 1 month to register your Peak Scientific product from the date of
installation. Once registered the warranty will be honoured for a period of 12
months. If you wish to defer the installation of your generator, you must notify
Peak Scientific immediately by emailing warranty@peakscientific.com. For
generators that remain unregistered after 1 month from the shipment date, the
warranty will be considered active from the date of factory dispatch.
Page 16

Page 17

Please visit www.peakscientific.com/downloads to
download the full User Manual for your gas generator.

Peak Scientific has highly trained, fully certified Field Service Engineers located in over 20 countries
across every continent around the world. This allows us to provide an industry-leading rapid response
service to our customers. With [Peak Protected], your laboratory’s productivity becomes our top
priority.
To discuss Peak Protected generator cover and payment options speak to your local Peak
Representative or for further information contact: protected@peakscientific.com.

Peak Scientific
Fountain Crescent
Inchinnan Business Park
Inchinnan
PA4 9RE
Scotland, UK
Tel: +44 141 812 8100
Fax: +44 141 812 8200
For further information on any of our
generator products please contact
marketing@peakscientific.com

Copyright © Peak Scientific Instruments Ltd 2017 — Infinity XE 50 Series Installation Guide Rev 2 PN UM-0019 RSID 2028 EN —05/12/2017

Search for similar resources

Remove