AMD 200 - Installation Guide (China Only)
Original PDF File1.1 MB |
Download |
View directly in browser1.1 MB |
View in browser |
Resource ID
2853
Access
Open
Contributed by
Derek Rennie
Updated date
12 December 19
Review date
01 May 24
Title
AMD 200 - Installation Guide (China Only)
Revision Number
2
Revision Details
Fittings Kit Update - LC
Keywords
Active, Carbon, Tower, ACT, Installation, Install, Manual, Guide
Product Range
*None
Language
UK English
Company Brand
Peak Scientific
Extracted text
AMD 200
Installation Guide
Copyright © Peak Scientific Instruments Ltd 2019 — AMD 200 Installation Guide Rev 2 RSID 2853 EN —12/12/2019
Change History
Rev
Comment
Name
Date
1
Initial Release
L. Couttie
23/01/2019
2
Fittings Kit Update
L. Couttie
12/12/2019
How to use this Installation Guide
This document is intended to be used only as a Quick Start Guide, to facilitate safe and
correct installation and initial configuration of your Peak Scientific gas generator.
For more extensive user operation directions, we recommend you download the User
Manual from the website.
Please visit www.peakscientific.com/downloads to
download the full User Manual for your gas generator.
Thank you for selecting Peak Scientific to meet your laboratory gas generation needs,
and should you require any further assistance or support please do not hesitate to
contact Peak Scientific or Peak Partner from which you purchased your generator.
Page 2
Safety Notices
Peak Scientific Instruments cannot anticipate every possible circumstance which may
represent a potential hazard. The warnings detailed within this document detail the
most known potential hazards, but by definition cannot be all inclusive. If the user
employs an operating procedure, item of equipment or a method of working which
is not specifically recommended by Peak Scientific, the user must ensure that the
equipment will not be damaged or become hazardous to persons or property.
Symbols
This document uses the following symbols to highlight specific areas important to the
safe and proper use of the unit
WARNING
A WARNING notice denotes a hazard. It calls attention to an operating procedure,
process or similar, which if not correctly performed or adhered to, could cause
personal injury or in the worst case death. Do not proceed beyond a WARNING
notice until the indicated conditions are fully understood or met.
CAUTION
A CAUTION notice denotes a hazard. It calls attention to an operating procedure,
process or similar, which if not correctly performed or adhered to, could cause
damage to the Generator or the Application. Do not proceed beyond a CAUTION
notice until the indicated conditions are fully understood or met.
Safety Notice to Users
WARNING
WARNING
These instructions must be read thoroughly and understood before
installation and operation of your Peak External Carbon Filter. Use of
this product in a manner not specified by Peak Scientific MAY impair
the SAFETY provided by the equipment.
When handling, operating or carrying out any maintenance, personnel
must employ safe engineering practices and observe all relevant local
health and safety requirements and regulations. The attention of UK
users is drawn to the Health and Safety at Work Act 1974, and the
Institute of Electrical Engineers regulations.
If the equipment is used in a manner not specified by the manufacturer,
the protection provided by the equipment may be impaired.
WARNING
Page 3
Fittings Kit
x2
¼” x 10mm push-fit elbow 02-4645
x3m
10mm PE Tubing 00-1294
x2
Bracket 06-6431
x4
No.8 Wall Plug 00-4076
x2
M4 Washer 00-1034
x4
No. 8 Screw 00-4075
Page 4
x2
M4 Screw 00-3008
1.
0°
0°
Unpack the unit from its container and position on a flat surface, in desired area.
2.
365 mm / 14.4”
136 mm / 5.4”
The generator can be wall mounted. The above image shows dimensions to drill holes
for the wall fixings.
If you do not wish to wall mount, proceed to step 4.
Page 5
3.
00-4076
00-4075
With the holes drilled in your desired location, fit the 3 x No.8 wall plug 00-4076 and
3 x No.8 screw 00-4075 to the wall and mount your generator onto them.
4.
06-6341
00-1034
00-3008
If the generator is not wall mounted using the key slots in the rear face, it must be
fixed to the wall using the brackets provided for safety reasons.
Locate the threaded holes on the right and left sides of the generator, beside the
yellow warning labels.
Page 6
Use the 00-3008 M4 screws and 00-1034 M4 washers provided to
attach the 06-6341 brackets onto the generator.
224 mm / 8.8”
00-4076
405 mm / 15.9”
5.
00-4075
Using the dimensions above, fix the No.8 wall plugs 00-4076 to the wall, ensuring
that the wall plugs provided are suitable for the type of wall in question. Secure the
generator to the wall with the No.8 screws 00-4075 from the fittings kit.
6.
02-4645
Select the 02-4645 ¼” x 10mm push-fit elbow and attach it to the filter outlet on the
right side of the generator. Attach the supplied 10mm PE tubing to the elbow and
connect the other end to the application.
Page 7
7.
02-4645
Select the 02-4645 ¼” x 10mm push-fit elbow and attach it to the
BA filter at the left side of the generator.
8.
00-1294
Attach the supplied 00-1294 10mm PE tubing to the elbow and
connect the other end to the air supply.
Page 8
9.
/
CONGRATULATIONS
Your Peak Scientific unit is now fully installed, operational and ready to supply gas on
demand to your instrument.
Page 9
Go Online or Complete and Return
We know that registering any of your recently purchased products is not the
first thing on your mind- but it is very important to both of us. Not all warranties
are alike and Peak Scientific stand out against other gas suppliers as we offer
a comprehensive on-site warranty. This means that in the very unlikely case
that your gas generator develops a fault we have rapid support teams on-hand
throughout the globe who are able to come to your lab and get you back up
and running in no time.
Register for your comprehensive 12 month on-site warranty with ease online at
www.peakscientific.com/protected.
Alternatively, you can send the completed form to Peak Scientific by post or
email at warranty@peakscientific.com.
Go Online or Complete and Return
You can register for your FREE 12 month Warranty with ease online at
www.peakscientific/protected.
Alternatively, you can send the completed form to Peak Scientific by post or
email at warranty@peakscientific.com.
Product Warranty Registration
Contact name
Email address
Company
Address
City/town
Postcode
Country
Telephone
Generator serial #
Model type
Installation date
Do you still use an
alternative gas solution i.e.
cylinders or bulk liquid?
Yes
What gas requirements do
you have in your lab?
Hydrogen
No
Nitrogen
Zero Air
Extend your cover with
Peak Scientific offer comprehensive gas generator after sales support packages.
Peak [Protected] aftercare support can guarantee an on-site response within
72 hours*, genuine parts from our ISO9001 approved factory and a 95% first-time
fix rate. See our enclosed Peak [Protected] leaflet for further information.
Important!
You have 1 month to register your Peak Scientific product from the date of installation. Once registered
the warranty will be honoured for a period of 12 months. If you wish to defer the installation of your
generator, you must notify Peak Scientific immediately by emailing warranty@peakscientific.com.
For generators that remain unregistered after 1 month from the shipment date, the warranty will be
considered active from the date of factory dispatch.
* Complete Plan only
Important!
You have 1 month to register your Peak Scientific product from the date of
installation. Once registered the warranty will be honoured for a period of 12
months. If you wish to defer the installation of your generator, you must notify
Peak Scientific immediately by emailing warranty@peakscientific.com For
generators that remain unregistered after 1 month from the shipment date, the
warranty will be considered active from the date of factory dispatch.
Page 10
Page 11
Please visit www.peakscientific.com/downloads to
download the full User Manual for your gas generator.
Peak Scientific has highly trained, fully certified Field Service Engineers located in over 20 countries
across every continent around the world. This allows us to provide an industry-leading rapid response
service to our customers. With [Peak Protected], your laboratory’s productivity becomes our top
priority.
To discuss Peak Protected generator cover and payment options speak to your local Peak
Representative or for further information contact: protected@peakscientific.com.
Peak Scientific
Fountain Crescent
Inchinnan Business Park
Inchinnan
PA4 9RE
Scotland, UK
Tel: +44 141 812 8100
Fax: +44 141 812 8200
For further information on any of our
generator products please contact
marketing@peakscientific.com
Copyright © Peak Scientific Instruments Ltd 2019 — AMD 200 Installation Guide Rev 2 RSID 2853 EN —12/12/2019